Lenovo HX1310 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 1002

background image

associated with power rail errors” on page 78, restarting the server each time, until the cause
of the overcurrent condition is identified.

Table 20. Components associated with power rail errors

Pwr rail error in the IMM event log

Components

Pwr rail 1 error

• Microprocessor 1

Pwr rail 2 error

• Microprocessor 2

Pwr rail 3 error

• DIMMs 1 through 12

• Fan 3

Pwr rail 4 error

• Fan 5

• Fan 6

• DIMMs 13 through 24

Pwr rail 5 error

• Fan 7

• Fan 8

• SAS/SATA hard disk drives and USB

Pwr rail 6 error

• Optional cable for VGA external power

• PCI-E and x16 (maximum expansion is 4 adapter cards)

• PCI-E hard disk drives

Pwr rail 7 error

• Fan 1

• Fan 2

d.

Replace the identified component.

Step 5.

Remove the adapters and disconnect the cables and power cords to all internal and external
devices until the server is at the minimum configuration that is required for the server to start (see
“Power-supply LEDs” on page 54 for the minimum configuration).

Step 6.

Reconnect all power cords and turn on the server. If the server starts successfully, reseat the
adapters and devices one at a time until the problem is isolated.

If the server does not start from the minimum configuration, see “Power-supply LEDs” on page 54 to replace
the components in the minimum configuration one at a time until the problem is isolated.

Solving Ethernet controller problems

The method that you use to test the Ethernet controller depends on which operating system you are using.
See the operating-system documentation for information about Ethernet controllers, and see the Ethernet
controller device-driver readme file.

Try the following procedures:

• Make sure that the correct device drivers, which come with the server are installed and that they are at

the latest level.

• Make sure that the Ethernet cable is installed correctly.

– The cable must be securely attached at all connections. If the cable is attached but the problem

remains, try a different cable.

– If you set the Ethernet controller to operate at 100 Mbps, you must use Category 5 cabling.

– If you directly connect two servers (without a hub), or if you are not using a hub with X ports, use a

crossover cable. To determine whether a hub has an X port, check the port label. If the label contains
an X, the hub has an X port.

78

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

«
...
90
91
92
93
94
...
»

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HX1310

Express5800/T110g-E

Бренд: NEC Страницы: 2

Бренд: Acano Страницы: 17

Бренд: Basalte Страницы: 2

Бренд: Patton electronics Страницы: 121

TJA670 domovea Basic

Бренд: hager Страницы: 36

8480 - Eserver xSeries 205

Бренд: IBM Страницы: 174

Portbase PB-3010

Бренд: SystemBase Страницы: 45

SuperServer 1026T-M3

Бренд: Supero Страницы: 104

Бренд: Sollae Systems Страницы: 27

Бренд: RackSolutions Страницы: 8

Бренд: Patton Страницы: 15

Бренд: AXIOMTEK Страницы: 76

SuperServer E301-9D-8CN8TP

Бренд: Supermicro Страницы: 117

ProLiant DL380 Gen9

Бренд: HPE Страницы: 8

Бренд: Acer Страницы: 52

Бренд: Acer Страницы: 94

Altos R700 Series

Бренд: Acer Страницы: 135

Бренд: Acer Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды