Lenovo HX1310 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 1002

Lenovo HX1310 Скачать руководство пользователя страница 59

Step 8.

Modify boot options. See “Modify boot options” on page 46.

Step 9.

Restart the server.

Configuring the HX Series appliance

This section contains configuration procedures that are used in one or more of the hardware replacement
procedures described in Chapter 5 “Removing and replacing components” on page 93.

Update the appliance name

The DMI/SMBIOS string for the Lenovo Converged HX Series appliance is the same as the appliance name.

Table 5. Appliance name and the corresponding VPD string

Appliance Name

VPD String

Lenovo Converged HX1310

Lenovo Converged HX1310

Lenovo Converged HX2310-E

Lenovo Converged HX2310-E

Lenovo Converged HX3310

Lenovo Converged HX3310

Lenovo Converged HX3310-F

Lenovo Converged HX3310-F

The DMI/SMBIOS string can be updated using the OneCLI system tool as follows:

onecli config set SYSTEM_PROD_DATA.SysInfoProdIdentifier “Lenovo Converged HX1310”
onecli config set SYSTEM_PROD_DATA.SysInfoProdIdentifierEx “Lenovo Converged HX1310:” –override

Legacy boot mode

The Lenovo ToolsCenter Suite CLI program, or other means should be used to enable if not already enabled.

onecli config set BootModes.SystemBootMode “Legacy Mode”

BIOS optimization settings

Lenovo recommends the following BIOS optimization settings to be used with the Lenovo Converged
HX Series appliances.

Direct cache access (DCA)

You should enable DCA mode for the processors to allow the network adapters to place data directly into the
CPU cache which reduces cache misses and can improve performance.

Use the Lenovo ToolsCenter Suite CLI program or other means to enable the DCA processor option:

onecli config set Processors.DCA Enable

Operating mode

You should change the operating mode from the default mode to

Custom Mode

. This permits other settings

to be changed such as the power performance bias.

Use the Lenovo ToolsCenter Suite CLI program or other means to set the operating mode:

onecli config set OperatingModes.ChooseOperatingMode “Custom Mode”

Power performance bias

.

45

«
...
57
58
59
60
61
...
»

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды