Lenovo HX1310 Скачать руководство пользователя страница 208

Страница: 208 / 1002

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0015

User Response

Information only; no action is required.

•

40000010-00000000 : Security: Userid: [arg1] had [arg2] login failures from WEB client at IP

address [arg3].

This message is for the use case where a user has failed to log in to a Management Controller from
a web browser.

May also be shown as 4000001000000000 or 0x4000001000000000

Severity

Warning

Serviceable

Automatically notify support

Alert Category

System - Remote Login

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0016

User Response

Complete the following steps until the problem is solved:

1. Make sure that the correct login ID and password are being used.

2. Have the system administrator reset the login ID or password.

•

40000011-00000000 : Security: Login ID: [arg1] had [arg2] login failures from CLI at [arg3].

This message is for the use case where a user has failed to log in to a Management Controller from
the Legacy CLI.

May also be shown as 4000001100000000 or 0x4000001100000000

Severity

Warning

Serviceable

194

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды