Lenovo HX1310 Скачать руководство пользователя страница 276

Страница: 276 / 1002

May also be shown as 4000009a00000000 or 0x4000009a00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Remote Login

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0154

User Response

Information only; no action is required.

•

4000009b-00000000 : Security: Userid: [arg1] had [arg2] login failures from IPMI serial client.

This message is for the use case where a user has failed to log in to a Management Controller from
IPMI serial client

May also be shown as 4000009b00000000 or 0x4000009b00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Remote Login

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0155

User Response

Information only; no action is required.

•

4000009c-00000000 : Remote Login Successful. Login ID: [arg1] from [arg2] serial interface.

This message is for the use case where a user successfully logs in to a Management Controller.

May also be shown as 4000009c00000000 or 0x4000009c00000000

262

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды