Lenovo HX1310 Скачать руководство пользователя страница 372

Страница: 372 / 1002

5. Replace the fans. (n = fan number)

•

800b010a-1e82ffff : Redundancy Lost for [RedundancySetElementName] has asserted. (Fan

Zone 2)

This message is for the use case when Redundancy Lost has asserted.

May also be shown as 800b010a1e82ffff or 0x800b010a1e82ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0802

User Response

1. Make sure that the connectors on fan n are not damaged.

2. Make sure that the fan n connectors on the system board are not damaged.

3. Make sure that the fans are correctly installed.

Reseat the fans.

5. Replace the fans. (n = fan number)

•

800b010c-2581ffff : Redundancy Lost for [RedundancySetElementName] has asserted. (Backup

Memory)

This message is for the use case when Redundancy Lost has asserted.

May also be shown as 800b010c2581ffff or 0x800b010c2581ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Memory

358

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды