Lenovo HX1310 Скачать руководство пользователя страница 855

Страница: 855 / 1002

•

W.58007 Invalid memory configuration (Unsupported DIMM Population) detected. Please verify

memory configuration is valid. Unsupported DIMM Population

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Ensure that the DIMM connectors are populated according to the guidelines in the service

information for this product.

2. Ensure all DIMMs are enabled in the uEFI setup menu.

3. If a DIMM connector error LED is lit, resolve the failure.

•

W.580A1 Invalid memory configuration for Mirror Mode. Please correct memory configuration.

Unsupported DIMM Population for Mirror Mode

Explanation:

Severity

Error

User Response

Complete the following steps:

1. If a DIMM connector error LED is lit, resolve the failure.

2. Make sure that the DIMM connectors are correctly populated for mirroring mode.

•

W.580A2 Invalid memory configuration for Sparing Mode. Please correct memory configuration.

Unsupported DIMM Population for Spare Mode

Explanation:

Severity

Error

User Response

Complete the following steps:

1. If a DIMM connector error LED is lit, resolve the failure.

2. Make sure that the DIMM connectors are correctly populated for sparing mode, according to

the service information for this product.

•

W.68002 A CMOS battery error has been detected CMOS Battery Fault

Explanation:

Severity

Error

User Response

Complete the following steps:

Appendix B. UEFI/POST diagnostic codes

841

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды