Lenovo HX1310 Скачать руководство пользователя страница 307

Страница: 307 / 1002

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat the failing fan n, which is indicated by a lit LED near the fan connector on the system

board.

2. Replace the failing fan. (n = fan number)

Fan 2B Tach :

•

80010204-1d03ffff : Numeric sensor [NumericSensorElementName] going low (lower critical)

has asserted. (Fan 3A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d03ffff or 0x800102041d03ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat the failing fan n, which is indicated by a lit LED near the fan connector on the system

board.

2. Replace the failing fan. (n = fan number)

Fan 3B Tach :

•

80010204-1d04ffff : Numeric sensor [NumericSensorElementName] going low (lower critical)

has asserted. (Fan 4A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d04ffff or 0x800102041d04ffff

Severity

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

293

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды