Lenovo HX1310 Скачать руководство пользователя страница 229

Страница: 229 / 1002

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0057

User Response

Information only; no action is required.

•

4000003a-00000000 : IPv6 static address of network interface modified from [arg1] to [arg2]

by user [arg3].

A user modifies the IPv6 static address of a Management Controller

May also be shown as 4000003a00000000 or 0x4000003a00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0058

User Response

Information only; no action is required.

•

4000003b-00000000 : DHCPv6 failure, no IP address assigned.

S DHCP6 server fails to assign an IP address to a Management Controller.

May also be shown as 4000003b00000000 or 0x4000003b00000000

Severity

Warning

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

215

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды