Lenovo HX1310 Скачать руководство пользователя страница 661

Страница: 661 / 1002

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0531

User Response

No action; information only. X8 PCI 3 Config :

•

810b010a-1e81ffff : Redundancy Lost for [RedundancySetElementName] has deasserted. (Fan

Zone 1)

This message is for the use case when Redundancy Lost has deasserted.

May also be shown as 810b010a1e81ffff or 0x810b010a1e81ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0803

User Response

No action; information only.

•

810b010a-1e82ffff : Redundancy Lost for [RedundancySetElementName] has deasserted. (Fan

Zone 2)

This message is for the use case when Redundancy Lost has deasserted.

May also be shown as 810b010a1e82ffff or 0x810b010a1e82ffff

Severity

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

647

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды