Lenovo HX1310 Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 1002

background image

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 100.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables.

Step 3.

Remove the cover (see “Removing the cover” on page 104).

Step 4.

If an adapter is installed in the PCI riser-card assembly, disconnect any cables that are connected
to the adapter.

Step 5.

Grasp both ends or the handle of the PCI riser-card assembly and lift it out of the PCI riser-card
slot on the system board. The following illustrations show the different PCI riser-card assembly
configurations that could be present in the server.

1U PCIe Riser 2 assembly
(1x full-height half-length; x16
and 1x low profile; x8 or x16)

1U PCIe Riser 1 assembly
(1x low profile; x16)

00000

00000

00000

00000

000000000

000000000

000000000

000000000

Figure 45. PCI riser-card assembly removal

Step 6.

Remove the adapter, if one is present, from the PCI riser-card assembly (see “Removing an
adapter” on page 125).

Step 7.

Set the adapter and the PCI riser-card assembly aside.

If you are instructed to return the PCI riser-card assembly, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Replacing a PCI riser-card assembly

Use this information to replace a PCI riser-card assembly.

Note:

PCI riser-card brackets must be installed even if you do not install an adapter.

The following table lists the supported PCI riser-card assembly configurations in the server.

Removing and replacing components

121

«
...
133
134
135
136
137
...
»

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HX1310

Бренд: Datacom Страницы: 89

EonServ 5000 Series

Бренд: Surveon Страницы: 33

N2400 - TaskSmart - 1 GB RAM

Бренд: Compaq Страницы: 372

NPort P5250A Series

Бренд: Moxa Technologies Страницы: 2

847620U - Netfinity 3000 - 20U

Бренд: IBM Страницы: 270

Бренд: Sun Oracle Страницы: 6

Бренд: Sun Microsystems Страницы: 12

UltraNEXUS HD Blade

Бренд: Leightronix Страницы: 5

Бренд: Cavalry Страницы: 16

Бренд: King Pigeon Страницы: 19

Бренд: Medion Страницы: 112

Xtreme PC NG6050

Бренд: Chip PC Страницы: 4

Бренд: Meinberg Страницы: 4

Бренд: Star Lake Страницы: 76

IP Video Surveillance

Бренд: C-MOR Страницы: 62

Бренд: SeeedStudio Страницы: 19

DSTni-XPress DR

Бренд: Lantronix Страницы: 2

Бренд: Intel Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды