Lenovo HX1310 Скачать руководство пользователя страница 662

Страница: 662 / 1002

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0803

User Response

No action; information only.

•

810b010c-2581ffff : Redundancy Lost for [RedundancySetElementName] has deasserted. (Backup

Memory)

This message is for the use case when Redundancy Lost has deasserted.

May also be shown as 810b010c2581ffff or 0x810b010c2581ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0803

User Response

No action; information only.

•

810b0309-1301ffff : Non-redundant:Sufficient Resources from Redundancy Degraded or Fully

Redundant for [RedundancySetElementName] has deasserted. (Power Resource)

This message is for the use case when a Redundancy Set has transitioned from Non-redundant:Sufficient
Resources.

May also be shown as 810b03091301ffff or 0x810b03091301ffff

Severity

648

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды