Lenovo HX1310 Скачать руководство пользователя страница 787

Страница: 787 / 1002

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0127

User Response

No action; information only.

•

816f070c-200affff : Configuration error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]has deasserted. (DIMM 10)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has deasserted.

May also be shown as 816f070c200affff or 0x816f070c200affff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0127

User Response

No action; information only.

•

816f070c-200bffff : Configuration error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]has deasserted. (DIMM 11)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has deasserted.

May also be shown as 816f070c200bffff or 0x816f070c200bffff

Severity

Info

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

773

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды