Lamtec CMS Скачать руководство пользователя страница 89

Страница: 89 / 284

Functional Description with Process Diagrams

Fig. 5-10 Gas train for standard sequence for gas modulating with pilot burner

Fig. 5-11 Oil train for standard process flow oil modulating with pilot burner

5.2.3

Purging the Fuel Train

Purging oil gun and gas train

This function is used to discharge residual fuel from an oil gun or gas train into the flame. If
the oil gun or gas train is purged then the 2

safety time (pilot valve and fuel valve open) is

increased at the next burner start sequence as the oil gun or gas train will have to be primed
again before ignition.

5.2.3.1 Requirements

The special curve point ’Purge oil gun’ must be configured.
How to set the special curve points see chapter

6.3.2 Configuring Special Points

5.2.3.2 Required Inputs/Outputs

For purging the oil gun, 2 additional logical input signals are required:
•

Purge valve

•

Atomiser steam valve

Gas side fuel valve

Gas damper servomotor

Burner side fuel valve

min

Min. gas pressure monitor

V3.1 Gas side pilot valve

V4.1 Burner side pilot valve

Содержание CMS





























































































































































































































































































Результаты поиска

Содержание CMS

Отзывы:

Похожие инструкции для CMS

Бренды по названию

Популярные бренды

Lamtec CMS, Руководство пользователя

Результаты поиска

Содержание CMS

Отзывы:

Похожие инструкции для CMS

Бренды по названию

Популярные бренды