manualshive.com logo in svg

Lamtec CMS, Руководство пользователя, Страница: 6 / 284

Поделиться
Скачать
Lamtec CMS Скачать руководство пользователя страница 6

5

Table of Contents

5.2.6.7 Suggested Circuit For Venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   100

5.3 

Electronic Ratio Control System  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   101
5.3.1  Requirements  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   101
5.3.2  Required Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   101
5.3.3  Required Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   101
5.3.4  Commissioning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   101
5.3.5  Physical actuator types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   101
5.3.5.1 Continuous Actuators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   101
5.3.5.2 Actuators with TPS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   102
5.3.6  Logical Actuator Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   102

5.4 

Burner Firing Rate Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   103
5.4.1  Requirements  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   103
5.4.2  Required Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   103
5.4.3  Required Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   103
5.4.3.1 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   103
5.4.3.2 I Term. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   104
5.4.3.3 Constant Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   104
5.4.3.4 Controlled by Atmospheric Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   104
5.4.3.5 Limiting the Firing Rate Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   105
5.4.3.6 Burner Shut-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   106
5.4.4  Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   107

5.5 

SPS Parameters  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   107

6 

Commissioning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   108

6.1 

Parameter and Password Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   108

6.2 

Commissioning Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   108

6.3 

Programming of Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   108
6.3.1  Programming Curves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   109
6.3.2  Configuring Special Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    110
6.3.3  Configuring the Range Limits  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    112
6.3.4  Shut-off Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    113
6.3.4.1 Run to Shut-off Limits  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    113
6.3.4.2 Checking the Shut-OFF Limits of the CMS with the CMS Remote Software  .    114
6.3.4.3 Checking the O2 Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    115

7 

Operating Control and Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    116

7.1 

Operation, Controls and Display with UI400  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    116
7.1.1  Menu Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    116
7.1.2  Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    118
7.1.3  Information Menu Path  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    118
7.1.3.1 Burner Details  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    119
7.1.3.2 Recalling Fault History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   120
7.1.3.3 Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   121
7.1.3.4 Display of Check Sums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   122
7.1.3.5 Positions of Actuators  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   122
7.1.3.6 Display IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   122
7.1.4  Manual Menu Path. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   123
7.1.5  Settings Menu Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   124
7.1.5.1 Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   124
7.1.5.2 Program Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   125

Содержание CMS





























































































































































































































































































Отзывы:

Нет отзывов