manualshive.com logo in svg

Lamtec CMS, Руководство пользователя, Страница: 3 / 284

Поделиться
Скачать
Lamtec CMS Скачать руководство пользователя страница 3

2

Table of Contents

Table of Contents

1 

Important Information about the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . . 8

1.1 

Validity of these Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . . 8

1.2 

References to Other Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . . 8

1.3 

Standards, Directives and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . . 8

1.4 

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 10

2 

Safety  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 12

2.1 

Classification of the Safety Instructions and Warnings  . . . . . . . . . . . . . . . . . . . . . . . .   . 12

2.2 

Target Group  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 13

2.3 

Product-specific Dangers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 13
2.3.1  Mounting Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 15
2.3.2  Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 16
2.3.3  Commissioning Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 17
2.3.3.1 Electronic Ratio Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 17
2.3.3.2 Basic Device  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 18
2.3.3.3 Parameter Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 18
2.3.3.4 FFS/ION/Terminal - Flame Tolerance Time . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 18
2.3.4  Electrical Connection Flame Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 19
2.3.5 CO/O

2

 Measuring Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 20

2.3.6  Acceptance and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 20
2.3.7  Components/Devices of External Manufacturers  . . . . . . . . . . . . . . . . . . . . . .   . 21

3 

System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 22

3.1 

Brief Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 22

3.2 

Digital Input/Output Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 24
3.2.1  Digital Inputs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 24
3.2.2  Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 26
3.2.3  Assignment of Input/Output Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 26
3.2.4  Chain Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 27
3.2.5  Curve Set Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 27

3.3 

Analogue Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 27
3.3.1  Analogue Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 27
3.3.2  Analogue outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 27

3.4 

Functional Description of the Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 28

3.5 

Life Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 29

4 

CMS Components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 30

4.1 

MCC – Master Control Component (burner module) . . . . . . . . . . . . . . . . . . . . . . . . . .   . 30
4.1.1  For Your Safety  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 30
4.1.2  Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 30
4.1.3  Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 32
4.1.4  LEDs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 32
4.1.5  Terminal Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 34
4.1.6  Connection Diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 35
4.1.7  Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 36

4.2 

AEC-TPS – Actuator Extension Component Three-Point Step . . . . . . . . . . . . . . . . . .   . 37
4.2.1  For Your Safety  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 37
4.2.2  Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 37
4.2.3  Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   . 39

Содержание CMS





























































































































































































































































































Отзывы:

Нет отзывов