manualshive.com logo in svg

Lamtec CMS, Руководство пользователя, Страница: 7 / 284

Поделиться
Скачать
Lamtec CMS Скачать руководство пользователя страница 7

6

Table of Contents

7.1.5.3 Configuring the Servomotors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   128
7.1.5.4 Setting Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   129
7.1.5.5 Deleting Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   130
7.1.5.6 Adjusting Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   131
7.1.5.7 Changing Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   132
7.1.5.8 UI400 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   132

7.2 

Operation, Controls and Display with GUI607/610/615 . . . . . . . . . . . . . . . . . . . . . . . .   133
7.2.1  Process Diagram and Menu Navigation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   134
7.2.2  Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   137
7.2.3  Burner Settings Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   138
7.2.4  Burner Firing-Rate Controller Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   148
7.2.5  CO/O2 Burner Optimisation Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   152
7.2.6  Flame Monitoring System Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   154
7.2.7  System Functions Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   155
7.2.8  User Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   162

7.3 

Operation, Controls and Display with CMS Remote Software. . . . . . . . . . . . . . . . . . .   164
7.3.1  Remote Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   164
7.3.1.1 Installation Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   164
7.3.1.2 Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   164
7.3.2  Offline/Online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   167
7.3.2.1 Offline Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   167
7.3.2.2 Online Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   168
7.3.2.3 Connecting the CMS to the PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   168
7.3.3  CMS Remote Software User Interface  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   172
7.3.3.1 Dataset Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   173
7.3.3.2 Connection Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   176
7.3.3.3 Access Rights Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   178
7.3.3.4 CMS Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   180
7.3.3.5 Options Menu  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   202
7.3.3.6 Help Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   205

8 CO/O

2

 Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  207

8.1 

For Your Safety  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  207

8.2 

Safety Concept  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   207

8.3 

Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  208

8.4 

Required Inputs/Outputs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   208

8.5 

Required Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   208

8.6 

Why Control CO?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   209
8.6.1  Where Can CO Control be Used? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   209
8.6.2  Overview of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   210
8.6.3  Optimisation Strategy  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    211
8.6.4  Advantages of CO Control over O

2

 Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    211

8.7 

Operating Control and Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    211
8.7.1  Is CO Control or O2 Trim Activated? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    211
8.7.2  Display in the Case of Active CO/O2 Control  . . . . . . . . . . . . . . . . . . . . . . . . .   213
8.7.2.1 Display with Active CO Control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   213
8.7.2.2 Display for Active O

2

 Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   213

8.7.2.3 Status Display in Case of O2 Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   213
8.7.2.4 Resetting Faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   214

8.8 

Electrical Connection - Connection via LSB  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   214

Содержание CMS





























































































































































































































































































Отзывы:

Нет отзывов