Kobelco SK235SR-2 Скачать руководство пользователя страница 81

Страница: 81 / 308

２

Turn starter key switch on and display main screen (a).

The screen is changed from "Digging" to "Nibbler" to "Breaker" each time the attachment mode

select switch (9) is turned when the main screen (a) is displayed.

Turn the switch (9) to "B", and "Nibbler mode" screen is displayed. Or turn the switch (9) to "A",

and "Breaker mode

”

screen is displayed.

When the nibbler/breaker select screen (b) or (c) is displayed, press the select switch (8) and the

value of flow rate reverses to black, and the screen is changed to (d). To increase flow, press the

up arrow (4) (washer switch), or to decrease flow, press the down arrow (5) (washer switch).

Select the desired setting value and then press select switch (8) and the flow rate is set to the

desired value.

［

2. MACHINE FAMILIARIZATION

］

2-19

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды