Kobelco SK235SR-2 Скачать руководство пользователя страница 53

Страница: 53 / 308

Battery acid or battery explosion can cause

serious injuries.

Before you service a battery, always wear face

protection, protective gloves and protective

clothing.

Batteries contain sulfuric acid. Avoid contact

with skin, eyes or clothing.

Antidote:

External: Flush with water.

Internal: Drink large quantity of water or milk.

Follow with milk of magnesia, beaten egg or

vegetable oil. Call physician immediately.

Eyes: Flush with water for 15 minutes and get

prompt medical attention.

・

Batteries give off explosive gases. Keep

all open flames, sparks and cigarettes away.

・

Always securely tighten cell caps.

・

Always securely tighten batteries terminals.

・

When batteries are charged, remove the

batteries from a machine. And charge the

batteries in a well ventilated area. At that

time, remove cell caps to allow gasses to

escape.

１

1.7

BATTERY SAFETY

A. BURN PREVENTION

B. BATTERY EXPLOSION PREVENTION

・

When the battery electrolyte is frozen, the battery can explode, if you try to charge the battery,

or you try to jump start and run the engine.

To prevent the explosion, warm the battery to 16 deg.C or higher.

・

When the battery electrolyte is frozen, the battery can explode, if you try to charge the battery,

or you try to jump start and run the engine.

To prevent the explosion, warm the battery to 16 deg.C or higher.

C. REPLACING THE BATTERIES

・

Turn the engine start switch to OFF.

・

When disconnecting the battery cables, always disconnect the negative (-) cable first. When

reconnecting the battery cables, always connect the positive (+) cable first.

・

If the metal items (Tools) bridge between the battery positive (+) terminal and the machine, the

short circuit occurs and sparks. It causes fire and explosion. Do not place the metal items

between the battery positive (+) terminal and the machine.

・

Do not invert battery terminals. Connect positive cable ends to positive (+) terminals and negative

cable ends to negative terminals (-).

Connect the negative (-) terminal to the upper-frame of the machine last.

［

1. SAFETY PRECAUTIONS

］

1-39

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды