Kobelco SK235SR-2 Скачать руководство пользователя страница 275

Страница: 275 / 308

Attachment

mode

Hydraulic circuit

Set pressure of

overload relief valve

ATT of single flow circuit like

breaker

Breaker mode

Return circuit does not pass

through control valve automatically.

When shipping: 24.5

MPa

(3550 psi)

ATT of conflux circuit like

nibbler

Nibbler mode

Return circuit pass through control

valve automatically.

When shipping: 24.5

MPa

(3550 psi)

The selector valve (1) is used to change the

flowing route of hydraulic oil.

Since the flow is automatically changed

according to the selected attachment mode,

the switching to proper attachment mode is

required depending on the attachment in use.

Switch the attachment mode referring to the

section "Attachment Mode Selection" in page

7-4.

Attachment mode

Mechatro controller

output

Hydraulic circuit

Mechatro controller input

Selector switching

valve

Piping

Selector switching

valve FB

Selector detecting

pressure FB

Digging / Nibbler

OFF

Nibbler

OFF

Breaker

７

Work mode and hydraulic circuit

-When the breaker is installed, make sure to select the breaker mode, because the return circuit

should return the oil to the return filter directly without passing through the control valve.

Select the breaker mode absolutely when you work with breaker.

-The overload relief valve is set to 24.5 MPa (3550 psi) when shipping from factory.

In some cases, the adjustment is required depending on the attachment, contact our dealer/distributor.

B. Switching Selector valve

When the "SELECTOR VALVE FAILURE" is displayed on the multi-display, there is a possibility that

the output and input signal of the mechatro-controller is different from the above-mentioned table.

Turn the attachment mode select switch to the required attachment mode again. When the

"SELECTOR VALVE FAILURE" does not disappear even if proper attachment mode is selected, since

it is suspected that it is caused by electrical failure, contact our dealer/distributor.

［

7. OPTIONAL EQUIPMENT

］

7-5

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды