Kobelco SK235SR-2 Скачать руководство пользователя страница 148

Страница: 148 / 308

F : Forward

N : Neutral (Stop)

R : Reverse

Make sure the safety lock lever is in the

"UNLOCKED" (down) position. Operate the

boom, arm, and bucket control levers to

raise the attachments from the ground.

To move the machine forward, push both

(right and left) travel levers toward the front

of machine. To move the machine in

reverse, pull back both travel levers.

Travel speed changes depending on how

far you push or pull the levers.

B. Machine Travel

-Identify the travel motor position before traveling. When the travel motor is positioned on the front side

the traveling operation reverses.

The normal traveling for the machine is that the travel motor is on the rear side and the track idler is

on the front side.

-Sound horn to warn workers in the site.

B.1 Forward/Reverse Travel

Forward/Reverse Travel

Do not move the travel speed switch during traveling. And change the travel speed in low (1st) speed

when the machine is running on the downhill, and is loading/unloading on/from trailer. The sudden

change of machine stability may cause accident resulting in injury and death.

When the travel alarm is installed, the travel alarm sounds by shifting the control lever with the travel

alarm switch turned "ON" to inform workers around the machine of the movement in travel operation.

［

3. MACHINE OPERATION

］

3-26

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды