Kobelco SK235SR-2 Скачать руководство пользователя страница 278

Страница: 278 / 308

Release pedal lock on the right front side of

driver's seat to operate pedal.

-Oil flow

The relation between the pedal position and the

direction of oil flow is shown in right figure.

-Nibbler (Crusher)

When the toe side (A) of pedal is depressed,

oil flows into left piping of attachment. And the

heel side (B) of pedal is depressed, oil flows

right piping of attachment. (In case of

BREAKER, pedal operation is only toe side.)

Breaker

Nibbler

Foot pedal depressing

section

Operation

Foot pedal depressing

section

Operation

Depess toe section (A)

Breaker starts operation

Depess toe section (A)

Nibbler close

Pedal in neutral position

Breaker stops operation

Depess heel section (B)

Nibbler open

B. Operating Pedal

ATTACHMENT OPERATION BY FOOT PEDAL

Always check the foot pedal control pattern before operation.

Always read operator's manual before operating machine.

Do not leave the machine with engine running.

［

7. OPTIONAL EQUIPMENT

］

7-8

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды