Kobelco SK235SR-2 Скачать руководство пользователя страница 114

Страница: 114 / 308

9. Setting Temperature Display Switching Function from/to F degrees to/from

C degrees

The setting temperature display can be switched from/to F degrees to/from C degrees.

While the fan is operating, press "

▼

" and "

▲

" switches (7) simultaneously for 5 seconds or more, and

the display is switched form/to Fahrenheit to/from Celsius. (But the unit is not displayed.)

10. Treatment of Season In and Off

(1) Season in

Contact our dealer/distributor for checking and service of air conditioner before air-cooling season

(season in) so that the air conditioner is used in good condition for a long time.

(2) Season off

Operate air conditioner for several minutes once a week in the period of out of season (season

off).

The operation maintains the air conditioner in good condition preventing short of oil in each part of

compressor.

［

2. MACHINE FAMILIARIZATION

］

2-52

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды