Kobelco SK235SR-2 Скачать руководство пользователя страница 39

Страница: 39 / 308

When the caution tag "Do not operate" or

similar warning is indicated on the control lever

or in the area around the cab, do not start

engine and do not touch the control lever.

１

1.5

SAFETY DURING OPERATION

STARTING ENGINE

PASSENGERS

This equipment is not intended or designed for the transportation of persons. Do not allow persons to

ride on the machine. Serious injury or death can result from allowing passengers on or in the machine.

SAFETY CHECK IN THE SURROUNDING BEFORE OPERATION

・

Check that no one is in the area around the machine.

・

Fix the door and window securely even though they are open or closed.

・

Adjust the mirror to the position where the operator can see well the rear sight.

For the adjustment, refer to "Adjusting Mirror" in Chapter 3.

・

Check that the alarm system like horn and travel alarm (if equipped) functions properly.

FASTEN SEAT BELT

Fasten seat belt so as to prevent receiving heavy blow inside of cab, being thrown out of the cab and

being crushed under the machine at the time when the machine turned over. If not fastened, it

causes serious injury or death.

Fasten seat belt without fail whenever taking the seat.

・

Check the attaching bracket and attaching belt for possible failure before fastening the seat belt.

・

Replace seat belt at least every 3 years even though no damage is found.

PRECAUTION TO BE TAKEN WHEN STARTING ENGINE

・

Lock it with the safety lock lever.

・

Sound the horn before starting the engine to alert people that the machine is being started.

・

Start engine from the operator's seat.

・

Do not short circuit the starter circuit or battery to start the engine. This may cause serious injury

or cause damage to the electrical system.

CHECK AFTER STARTING ENGINE

Check the machine for proper operation after starting the engine. Slowly cycle attachments, swing,

and travel functions in an area with sufficient space, without obstacles and personnel. Failure to do

so could result in injury, death or machine damage. If any problems or damage is found on the

machine, repair immediately.

WARM UP ENGINE AND HYDRAULIC OIL BEFORE OPERATION

Take time to warm up the engine and hydraulic oil especially during cold season. In cold conditions,

response of machine control is slow. This may cause injury, death or machine damage.

［

1. SAFETY PRECAUTIONS

］

1-25

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды