Kobelco SK235SR-2 Скачать руководство пользователя страница 156

Страница: 156 / 308

Operate the bucket at shallow depths and use

the arm in action to fill the bucket. Setting the

bucket too deep will decrease the machine's

efficiency.

Always begin and end boom operation slowly

with smooth, careful movement of the control

lever. Do not perform sudden starts and stops

of the boom as this creates unnecessary

stress on the machine and its components.

Always point bucket teeth in the direction the

machine will be digging to reduce digging

resistance and the possibility of bucket teeth

damage.

The attachment will provide maximum digging

force when the arm and boom are at 90 to 110

degrees of each other.

3.1.14

PRACTICES TO IMPROVE EFFICIENCY

A. Use Arm in Action

B. Operate Boom Smoothly

C. Bucket Teeth Direction

D. Maximum Digging Force Position

［

3. MACHINE OPERATION

］

3-34

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды