Kobelco SK235SR-2 Скачать руководство пользователя страница 35

Страница: 35 / 308

・

Do not smoke close to the area and do

not use the fire near the area.

・

Make up shortage of fuel after stopping the

engine.

・

During making up shortage of fuel and oil,

do not leave the place.

・

Tighten caps for fuel and oil securely.

・

Make sure not to spill out oil on the heated

surface and the parts for electric system.

・

Store fuel and oil in the specified place

and keep out of the area excluding persons

concerned.

・

After refueling and lubrication, wipe off the

spilled out fuel and oil, etc. immediately.

・

Move the inflammables to the safe area

before carrying out the grinding and welding

works of machine.

・

Use incombustible washing as wash oil for

parts, etc. and do not use light oil and

gasoline which might catch fire.

・

Do not weld the pipes and tubes containing

combustible liquid and do not employ gas

cutting.

１

M. FIRE PREVENTION

Fire due to Fuel and Oil

There is a possibility of catching fire by bringing fire near inflammables like fuel, oil, antifreeze

mixture, window washer, etc.

Follow precaution described below.

Fire due to Faulty Electric Wire

The fire may be caused by short-circuit of electric wire.

・

Keep all connectors of electric wire clean and fix them securely.

・

Check the wire for loosening and damage every day, and tighten loose connectors and clamps

for wiring again and replace the damaged wire with new one.

Fire due to Faulty Piping

Check that the clamp, guard and cushion of hose and tube are securely fixed. The loosening may

cause the damage of hose due to the vibration during operation and the scrubbing in contact to other

parts and is in danger of fire and accident resulting in injury or death due to the spouting out of high

pressure oil.

Use Approved Work Lights

Use only approved work lights when performing inspection and maintenance procedures to prevent

possible fire or explosion. Certain types of work lights should not be used due to the possibility of

ignition of certain flammable gasses and fluids from the machine.

［

1. SAFETY PRECAUTIONS

］

1-21

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды