Kobelco SK235SR-2 Скачать руководство пользователя страница 44

Страница: 44 / 308

There is a possibility of accident resulting in

injury or death and the damage of machine due

to the fall of sand/earth and the direct contact

with bucket when the bucket and attachment

pass through over the worker and the driver's

seat of dump truck. Do not pass the bucket

through over person for safety.

Make sure the condition of the work site is

stable and capable of supporting the machine

weight during operation. Do not operate

attachment too close to the machine. Operation

of the machine on shoulders or filled areas

could cause the machine to become unstable

presenting a work hazard. Position the crawler

at right angle to shoulder and the travel

motors to the rear of the machine, allowing for

quick reversal, should the work area become

unstable.

CHECK THAT NO PERSON IS UNDER THE BUCKET

GROUND STABILITY

W. LIFTING

Before operating the machine, make sure the job-site of machine is clear of all persons and

obstacles. And park the machine on the hard and level ground. If the machine is equipped with the

level gauge, confirm the inclination of the machine with the level gauge. Do not use the tooth of

bucket for lifting load. Lift the load with a special lifting device such as hook.

The machine for Australia equips the level gauge as standard equipment.

［

1. SAFETY PRECAUTIONS

］

1-30

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды