Kobelco SK235SR-2 Скачать руководство пользователя страница 142

Страница: 142 / 308

3.1.10

MACHINE WARMING-UP

-The proper hydraulic oil temperature for this machine is about 50 C degrees.

The abrupt operation when the hydraulic oil temperature is 25 C degrees or less may cause serious

trouble for hydraulic equipment. Warm up the hydraulic oil before starting the work.

-The operation of attachment with insufficient warming-up makes the reaction of attachment to the

control lever slower and may move the attachment against the purpose of operator. Do not fail to

perform the warming-up.

Especially in cold weather, the sufficient warming-up is necessary.

Perform the warming-up by the following procedure.

A. Engine Warm-Up

-The revolution up of engine while idling may cause failure and trouble to the engine. Do not

revolution up the engine while idling.

-In warning-up the engine, turn auto idling stop function switch OFF.

Allow the engine to run for 5 minutes under no load conditions with throttle potentiometer (1) at

"LO" idle position.

When the pointer of engine coolant temperature (2) moves and points to the range in white, the

warming-up of engine is completed.

For the engine start procedure with auto warming-up system, see "2.3.1.B.8.1

Auto Warming Up".

［

3. MACHINE OPERATION

］

3-20

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды