Kobelco SK235SR-2 Скачать руководство пользователя страница 31

Страница: 31 / 308

Located inside cab R.H.

Part Number - YN20T01695P1

１

29. ENGINE AUTO IDLING STOP

When you stand up and or move over the control levers during operation, your body or hand may

contact the levers and resulting unexpected movement of attachments or upper machinery.

Make sure to set the safety lock lever for inoperative position before you stand up and move from

operators' seat.

Auto idle stop (AIS) system will stop engine and any motive power and may result accident if using

machine for lifting work.

Make sure to turn off the AIS system when using machine for lifting work.

Make sure the following cautions when using Auto Idle Stop (AIS) system.

-After AIS system activates and stops engine, make sure to turn the starter key "ACC" or "OFF"

position once, set accelerator dial to Lo speed range then start engine. If AIS system sounds alarm,

engine will not be started till the sound will be stopped.

-Make sure to turn the starter key "OFF" position when you leave the machine for a while.

-AIS system will not activate when multi display monitor indicates an error of engine coolant

temperature.

［

1. SAFETY PRECAUTIONS

］

1-17

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды