Kobelco SK235SR-2 Скачать руководство пользователя страница 273

Страница: 273 / 308

７

7.1

OPERATION OF HYDRAULIC BREAKER AND NIBBLER (FOR

1 PEDAL TYPE)

7.1.1

SELECTION OF HYDRAULIC BREAKER AND NIBBLER

When installing a hydraulic breaker or nibbler to the machine, select the optimal breaker or nibbler

taking the matters into consideration such as stability, hydraulic system pressure, required hydraulic oil

volume.

7.1.2

BEFORE OPERATING BREAKER OR NIBBLER

・

Consult with your Dealer for the additional piping work and reinforcement for the arm to install

the breaker or nibbler to the machine.

・

When using the breaker or nibbler, fully understand and peruse the operation manual of its

manufacturer and the PROHIBITED WORK IN USE OF BREAKER" page 7-10 for the work

mentioned in this MANUAL, in order to get full performance of them paying attention to damages

on the machine and hydraulic breaker or nibbler.

7.1.3

PRECAUTIONS FOR IMPURITY AND HYDRAULIC OIL

When the hydraulic breaker or nibbler is removed after its installation, apply a blinding plug to the stop

valves attached on the tip of arm and openings on the hydraulic pipings for the hydraulic breaker or

nibbler to prevent them from invasion of dust, water, etc.

Before the operation, check the looseness on the clamps which are fixing the piping for attachment,

and the leakage on connections of tubes and hoses.

7.1.4

ATTACHMENT MODE SELECTION AND SELECTOR VALVE

A. Selection of Attachment Mode

In accordance with the attachment which is equipped, it is necessary to change the attachment mode.

･

Select the attachment mode appropriately when you use the breaker or nibbler. Confirm the position

of attachment mode switch and the screen of multi display closely.

･

Turn the attachment mode switch to a correct position when the switch position is improper. Match

the attachment mode to the attachment that is used from now.

･

Select the breaker mode absolutely when you work with breaker. If the machine is operated with

mode other than breaker mode, hydraulic component and breaker are damaged.

･

If the selection of attachment mode is not correct, it causes defective operation and the breakdown of

the machine.

･

When "H" or "S" of the fuel consumption mode is flickering, this shows that the selection of

attachment mode is improper.

［

7. OPTIONAL EQUIPMENT

］

7-3

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды