Kobelco SK235SR-2 Скачать руководство пользователя страница 212

Страница: 212 / 308

This machine is equipped with belts for

alternator, fan and air-con.

Check these belts for wear and damage and

check the belt tension for slack, and adjust it

properly in order to maintain the engine in

high performance and the specified service life.

Check the tension of belt by pressing on the

center of belt by thumb. If the deflection is

within the range shown in the table, it is in

normal tension.

Belt

When new belt replaced

mm (in)

When inspected

mm (in)

Force

N (lbf)

Alternator, Fan

8 to 10 mm (0.31 to

0.39")

10 to 12 mm (0.39 to

0.47")

98 (22)

Air-conditioner

6 to 7 mm (0.24 to 0.28")

7 to 8 mm (0.28 to 0.31")

28 (6.3)

4.14

250 HOUR (3-MONTH) INSPECTION & MAINTENANCE

PROCEDURE

Thoroughly read and understand the "1.SAFETY PRECAUTIONS" of this MANUAL before operating or

servicing the machine.

Perform together with daily, 50-hour and 120-hour inspection and maintenance.

Fan, Alternator, A/C Belt Wear and Tension

Rotating parts can cause injury. Keep away from fan and belt when engine is running. Stop engine

before servicing.

-When replace with new belt, there is a lack of initial adaptability of the belt. Run the engine at idling

speed for about three or five minutes. After that, adjust the belt tension again.

-New belts get complete initial elongation after being run about two hours.

-When you replace V-belts which are two in on set, make sure to replace both of them.

Adjustment for Alternator and Fan Belt

Be careful of the alternator and fan belts so that grease and oil are not adhered. The service life

may be shortened due to slipping with oil.

［

4. MAINTENANCE

］

4-44

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды