Kobelco SK235SR-2 Скачать руководство пользователя страница 297

Страница: 297 / 308

８

8.1

GENERAL

The SK235SRLC-2 machine incorporates automatically applied spring brake systems in the travel

motors and swing motors. These systems will automatically engage the brakes when engine is stopped

making it impossible to move the machine.

This section contains the required procedures for releasing the travel motor brakes, the swing motor

brake and lowering the attachment to the ground should sudden engine failure be experienced.

Make certain chock blocks are secure at front and rear of each track before attempting to release

brakes.

Never stand in the path of the tracks when releasing brakes.

Read, understand and follow all safety precautions and procedures found in this manual before

attempting any operation, inspection, maintenance or repair of this machine, attachment or any of its

systems.

The procedures found in this section should be performed by a well trained experienced service

technician who is familiar with the KOBELCO SK235SRLC-2 machines.

［

8. SPECIAL PROCEDURES

］

8-3

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды