Kobelco SK235SR-2 Скачать руководство пользователя страница 69

Страница: 69 / 308

After turning starter key switch ON or starting

engine, the screen is changed in order of "Time

for engine oil change" --> "Time for fuel filter

replacement" --> "Time for hydraulic oil filter

change" --> "Time for hydraulic oil change" -->

"Main screen" each time the screen change

switch (2) is pressed.

With this menu, the time range to the

recommended change time for the filter and oil

in use can be identified.

In case where warning is displayed on the

multi-display (LCD), press buzzer stop switch (1)

and buzzer shown below stops sounding.

２

SCREEN CHANGE SWITCH

If the screen change switch is not operated for 30 seconds keeping the screen for maintenance

displayed, the screen automatically reruns to the main screen.

BUZZER STOP SWITCH

The level shown in the table is based on the following contents.

1. This warning shows the condition of personal injury or machine function.

2. This warning shows the change of work mode.

3. This might lead to the failure of machine. Check and service it immediately.

［

2. MACHINE FAMILIARIZATION

］

2-7

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды