Kobelco SK235SR-2 Скачать руководство пользователя страница 54

Страница: 54 / 308

Put attachment on the ground, return all

control levers to neutral position and then

lock the safety lock lever.

Set the starter key switch to "OFF" for both

boost vehicle and disabled machine.

Connect the booster cable (red) clip to the

positive (+) terminal on the battery of

disabled machine.

Connect the clip from the other end of the

positive (+) booster cable (red) to the

positive (+) terminal on the battery of boost

vehicle.

D. USING BOOSTER CABLES TO START THE ENGINE

1. Use the same capacity battery of disabled battery for boosting battery.

2. Connect clip of booster cables securely.

3. Check that the safety lock lever is in the locked position.

4. Check that control lever was returned to neutral position.

5. Turn off both starter key switches of normal machine and troubled machine. When the machine is

powered on, machine may unexpectedly start and it causes accident.

Procedure:

Connect the booster cable (black) clip to the negative (-) terminal on the battery of boost vehicle.

Finally, connect the clip from the other end of the negative (-) booster cable (black) to the upper

frame of disabled machine, away from the battery.

Start the engine of boost vehicle, and run it for about 10 minutes at high idle.

Start the engine of disabled machine.

After starting the engine of disabled machine, remove the booster cables in the reverse order of

the above connection order.

10. Check and repair the cause of the problem of the charging system on the disabled machine.

E. DISPOSE OF WASTE PROPERLY

・

Turn the engine start switch to OFF.

・

When disconnecting the battery cables, always disconnect the negative (-) cable first. When

reconnecting the battery cables, always connect the positive (+) cable first.

・

If the metal items (Tools) bridge between the battery positive (+) terminal and the machine, the

short circuit occurs and sparks. It causes fire and explosion. Do not place the metal items

between the battery positive (+) terminal and the machine.

・

Do not invert battery terminals. Connect positive cable ends to positive (+) terminals and negative

cable ends to negative terminals (-).

Connect the negative (-) terminal to the upper-frame of the machine last.

［

1. SAFETY PRECAUTIONS

］

1-40

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды