Kobelco SK235SR-2 Скачать руководство пользователя страница 194

Страница: 194 / 308

After the radiator cap/cooling system has

cooled so it can be touched with a bore

hand, slowly loosen the cap (1) to release

the pressure.

After all pressure is released, remove the

radiator cap.

Check the cap for damage or contamination.

Clean it and/or replace it if needed.

Securely tighten the cap.

Check wiper blade for wear and damage,

replace it if necessary.

4.10

WHEN REQUIRED

Thoroughly read and understand the Section 1 "SAFETY PRECAUTIONS" of this MANUAL before

operating or servicing the machine.

Cleaning or Replacement of Radiator Cap

To avoid being burned, be careful when removing the radiator cap. Coolant is under high pressure

when hot.

-Do not remove the radiator cap when the system is hot.

-Allow enough time for the machine to cool down before removing the radiator cap.

A loose radiator cap will let hot steam and coolant escape from the cooling system. Allow the radiator

cap/cooling system enough time to cool before tightening the loose cap.

Checking and Replacing Wiper Blade

［

4. MAINTENANCE

］

4-26

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды