Kobelco SK235SR-2 Скачать руководство пользователя страница 118

Страница: 118 / 308

Push door against catch (1) and door is

fixed.

When necessary to open the door, push

down lever (2) on the left side of operator

seat and the catch is released.

When necessary to fix the door, fix door

to the catch securely.

When necessary to open the door from the

inside of cab, pull lever (3) by hand and the

door opens.

2.3.13

OPERATOR CAB

When necessary to leave from the operator seat, lock the safety lock lever.

After the control lever is unexpectedly touched without the safety lock lever locked, this may cause

serious accident resulting in injury and death.

A. Cab Door Lock

This is used to fix door in the condition where the door is open.

In operation, lock the door securely even if it is on either open side or close side. When not locked,

the door may be open unexpectedly and this might cause the injury. And also it may cause the failure

of machine.

B. Releasing Door Lock from Inside of Cab

［

2. MACHINE FAMILIARIZATION

］

2-56

Содержание SK235SR-2



























































































































































































































































































Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды

Kobelco SK235SR-2, Руководство по эксплуатации

Результаты поиска

Содержание SK235SR-2

Отзывы:

Похожие инструкции для SK235SR-2

Бренды по названию

Популярные бренды