Juniper JUNOS 10.1 - S 5-13-2010 Скачать руководство пользователя страница 9

Страница: 9 / 204

■

GMRP

■

GVRP

■

LACP

■

PVST

■

xSTP

The Layer 3 protocols supporting the preclassifier are:

■

IGMP

■

IPv4/IPv6 ICMP

■

IPv4/IPv6 ISIS

■

IPv4/IPv6 OSPF

■

IPv4/IPv6 PIM

■

IPv4 Router Alert

■

IPv4/IPv6 RSVP

■

IPv4/IPv6 VRRP

The Layer 4 protocols supporting the preclassifier are:

■

IIPv4/ IPv6 BGP

■

IPv4/ IPv6 LDP

■

IPv4 UDP/L2TP

■

RIP (UDP port checks)

The preclassifier is also supported on label-switching encapsulation PPP.

[

Class of Service

]

■

Feature support on 16-port 10-Gigabit Ethernet MPC with SFP+ (MX Series
routers)

—The following features are supported on the 16-port 10-Gigabit Ethernet

MPC with SFP+:

■

Accepts traffic destined for GRE tunnels or DVMRP (IP-in-IP) tunnels (JUNOS
Release 10.0R2)

■

Bidirectional Forwarding Detection (BFD) protocol (JUNOS Release 10.0R2)

■

Border Gateway Protocol (BGP) (JUNOS Release 10.0R2)

■

BGP/Multiprotocol Label Switching (MPLS) virtual private networks (VPNs)
(JUNOS Release 10.0R2)

■

Distance Vector Multicast Routing Protocol (DVMRP) and generic routing
encapsulation (GRE) support, access side and server side (JUNOS Release
10.0R2)

■

Firewall filters (JUNOS Release 10.0R2)

New Features in JUNOS Release 10.1 for M Series, MX Series, and T Series Routers

■

New Features in JUNOS Release 10.1 for M Series, MX Series, and T Series Routers

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Результаты поиска

Содержание JUNOS 10.1 - S 5-13-2010

Отзывы:

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Бренды по названию

Популярные бренды

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

Результаты поиска

Содержание JUNOS 10.1 - S 5-13-2010

Отзывы:

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Бренды по названию

Популярные бренды