manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

"Juniper JUNOS 10.1 - S 5-13-2010" - это последнее обновление программного обеспечения от Juniper Networks. В этом выпуске содержатся важные изменения и улучшения. Вы можете скачать бесплатное руководство по обновлению и использованию этого продукта на manualshive.com. Будьте в курсе всех нововведений с нашими Release Notes.

Поделиться
Скачать
background image

■

On EX2200 switches, the MIB OID 

ipv6Forwarding

 indicates that IPv6 is supported

even though IPv6 is not supported. The value of the 

ipv6Forwarding.0

 MIB object

is 1. [PR/473128]

■

If you attempt to set the time zone to 

Europe/Berlin

 on a switch with dual Routing

Engines, the 

commit

 command might fail. [PR/483273]

Interfaces

■

On EX8200 switches, aggregated Ethernet interfaces might go down and come
back up for a few minutes while the switch is updating many routes. [PR/416976]

J-Web Interface

■

In the J-Web interface, you cannot commit some configuration changes in the
Ports Configuration page and VLAN Configuration page because of the following
limitations for port mirroring ports and port mirroring VLANs:

■

A port configured as the output port for an analyzer cannot be a member of
any VLAN other than the default VLAN.

■

A VLAN configured to receive analyzer output can be associated with only
one port.

[PR/400814]

■

In the J-Web interface, uploading a software package to the switch might not
work properly if you are using Internet Explorer version 7. [PR/424859]

■

If an SRE module, RE module, SF module, line card, or Virtual Chassis member
is in offline mode, the J-Web interface might not update the dashboard image
accordingly. [PR/431441]

■

In the J-Web interface, in the Port Security Configuration page, you are required
to configure 

action

 when you configure 

MAC limit

 even though configuring an

action

 value is not mandatory in the CLI. [PR/434836]

■

In the J-Web interface, in the OSPF Global Settings table in the OSPF Configuration
page, the Global Information table in the BGP Configuration page, or the Add
Interface window in the LACP Configuration page, if you try to change the position
of columns using the drag-and-drop method, only the column header moves to
the new position instead of the entire column. [PR/465030]

■

In the J-Web interface, in the OSPF Configuration page (

Configuration > Routing

> OSPF

), the Traceoptions tab in the Edit Global Settings window does not

display the available flags (tracing parameters). As a workaround, use the CLI to
view the available flags. [PR/475313]

■

When you have a large number of static routes configured and if you have
navigated to pages other than page 1 in the Route Information table in the J-Web
interface (

Monitor > Routing > Route Information

), changing the 

Route Table

to query other routes refreshes the page but does not return to page 1. For
example, if you run the query from page 3 and the new query returns very few
results, the Results table continues to display page 3 and shows no results. To
view the results, navigate to page 1 manually. [PR/476338]

Outstanding Issues in JUNOS Release 10.1 for EX Series Switches

■

193

Outstanding Issues in JUNOS Release 10.1 for EX Series Switches

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Garmin eTrex H - Hiking GPS Receiver Owner'S Manual preview
eTrex H - Hiking GPS Receiver
Бренд: Garmin Страницы: 100
Waves Linear-Phase MultiBand Software Audio Processor User Manual preview
Linear-Phase MultiBand Software Audio Processor
Бренд: Waves Страницы: 27
Acuma Labs De-Esser User Manual preview
De-Esser
Бренд: Acuma Labs Страницы: 20
Baracoda KEmul RS232 User Manual preview
KEmul RS232
Бренд: Baracoda Страницы: 9
Oberheim Matrix-1000 Owner'S Manual preview
Matrix-1000
Бренд: Oberheim Страницы: 64
Teklynx Form Designer User Manual preview
Form Designer
Бренд: Teklynx Страницы: 30
Polycom Conference Composer User Manual preview
Conference Composer
Бренд: Polycom Страницы: 29
Extron electronics AVT 100 User Manual preview
AVT 100
Бренд: Extron electronics Страницы: 37
GameShark GAME CUBE Instruction Manual preview
GAME CUBE
Бренд: GameShark Страницы: 16
GRASS VALLEY KAYAK HD-SD Datasheet preview
KAYAK HD-SD
Бренд: GRASS VALLEY Страницы: 8
GRASS VALLEY K2 FCP CONNECT - Release Note preview
K2 FCP CONNECT -
Бренд: GRASS VALLEY Страницы: 19
DigiDesign Video Satellite LE Manual preview
Video Satellite LE
Бренд: DigiDesign Страницы: 17
Xilinx System Generator V2.1 Reference Manual preview
System Generator V2.1
Бренд: Xilinx Страницы: 148
TANDBERG MOVI 4.0 - FOR WINDOWS 09-2010 User Manual preview
MOVI 4.0 - FOR WINDOWS 09-2010
Бренд: TANDBERG Страницы: 19
Garmin 010-10844-00 - Mobile XT - GPS Software Owner'S Manual preview
010-10844-00 - Mobile XT - GPS Software
Бренд: Garmin Страницы: 52
Waves Digital Audio Effects Processor Doubler User Manual preview
Digital Audio Effects Processor Doubler
Бренд: Waves Страницы: 6
GE v6 User Manual preview
v6
Бренд: GE Страницы: 269
Asus Security Protect Manager User Manual preview
Security Protect Manager
Бренд: Asus Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды