manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

"Juniper JUNOS 10.1 - S 5-13-2010" - это последнее обновление программного обеспечения от Juniper Networks. В этом выпуске содержатся важные изменения и улучшения. Вы можете скачать бесплатное руководство по обновлению и использованию этого продукта на manualshive.com. Будьте в курсе всех нововведений с нашими Release Notes.

Поделиться
Скачать
background image

■

In some cases during the periodic error status monitoring, error messages such
as “Wi seg ucode discards in fabric stream” may be displayed on adjacent
streams. These messages are cosmetic and can be ignored. [PR/481344: This
issue has been resolved.]

■

When loopback is configured on t3 under ct3, t1 under ct1, or e1 under ce1, no
error syslog message is logged. Additionally, the 

show interface extensive

command on the t3/t1/e1 displays "loopback" even though it is not actually
applied. [PR/486424: This issue has been resolved.]

■

The DPC remains in the ready state and the demux0 interface remains in a down
state after a chassisd restart without graceful Routing Engine switchover (GRES)
enabled. [PR/492961: This issue has been resolved.]

■

The AE logical interface flaps when the PIC that has the active link-protection
member link is taken offline. [PR/493492: This issue has been resolved.]

■

The No Redundant Config alarm that occurs in JUNOS Release 10.0 and above
after a PEM is shut down is invalid and is a non-impacting alarm message.
[PR/498089: This issue has been resolved.]

■

The one port OC12-3 PIC cannot support eight queues when the 

no-concatenate

option is configured. [PR/499452: This issue has been resolved.]

■

On a 4–port ChOC3/STM1 and 12–port T1/E1 circuit emulation PICs, the ATM
logical interface packets counter does not increment if the PIC is configured in
the ATM IMA mode. [PR/500153: This issue has been resolved.]

■

When t1-options are configured at the 

[edit interfaces ct1-x/y/z]

 hierarchy level,

some ct1 interfaces of a 10xCHT1 IQ PIC might flap when the configuration
changes are committed. As a workaround, remove the t1-options. [PR/500820:
This issue has been resolved.]

■

Polling 

ifInOctets

 on Gigabit Ethernet IQ PIC VLANs might momentarily return a

higher value. [PR/500852: This issue has been resolved.]

■

On 40x1 Gigabit Ethernet PICs, very short fragments of fragmented TCP, UDP,
and ICMP packets may be incorrectly dropped with the diagnostic L4 length too
short. [501526: This issue has been resolved.]

■

The configured TTL set for GRE traffic is set properly for locally generated Routing
Engine packets, but is not set properly for transit packets. There is no
workaround. [PR/502087: This issue has been resolved.]

■

During a link UP/DOWN transition, jsscd may crash as a result of a NULL message
dereferencing by jsscd. [PR/502745: This issue has been resolved.]

■

In JUNOS Release 10.1, if the Neo MPCs power up while the A-DPCs are offline,
and if ISSU is performed, the MPCs will crash. [PR/502837: This issue has been
resolved.]

■

When an ATM AIS cell is received from the virtual channel under vlan-vci-ccc
encapsulation, the logical interface will be incorrectly marked down. There is no
workaround. [PR/503653: This issue has been resolved.]

■

When the 

show lacp interface aex

 command is used for a nonexistent AE interface,

no error is returned. [PR/503806: This issue has been resolved.]

Issues in JUNOS Release 10.1 for M Series, MX Series, and T Series Routers

■

67

Issues in JUNOS Release 10.1 for M Series, MX Series, and T Series Routers

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

UMAX Technologies PowerColor Quick Start Manual preview
PowerColor
Бренд: UMAX Technologies Страницы: 10
AMX WebLinx Instruction Manual preview
WebLinx
Бренд: AMX Страницы: 50
Sigma PHOTO PRO 4.2 Manual preview
PHOTO PRO 4.2
Бренд: Sigma Страницы: 55
Crestron SIMPL Windows Installation & Operating Manual preview
SIMPL Windows
Бренд: Crestron Страницы: 230
Sharp PixLab Online Manual preview
PixLab
Бренд: Sharp Страницы: 12
Tascam HS-P82 Release Note preview
HS-P82
Бренд: Tascam Страницы: 6
Linux LINUX ENTERPRISE DESKTOP 10 SP1 - Manual preview
LINUX ENTERPRISE DESKTOP 10 SP1 -
Бренд: Linux Страницы: 76
British Telecom Tyne Operating Instructions & User Manual preview
Tyne
Бренд: British Telecom Страницы: 4
Red Hat CLUSTER SUITE FOR ENTERPRISE LINUX 4.5 Installation Manual preview
CLUSTER SUITE FOR ENTERPRISE LINUX 4.5
Бренд: Red Hat Страницы: 110
Symantec Norton Antispam Personal Firewall and Systemwork - Norton Antispam User Manual preview
Norton Antispam Personal Firewall and Systemwork - Norton Antispam
Бренд: Symantec Страницы: 33
Symantec NORTON 360 5.0 User Manual preview
NORTON 360 5.0
Бренд: Symantec Страницы: 40
Symantec NORTON GHOST User Manual preview
NORTON GHOST
Бренд: Symantec Страницы: 80
Symantec OLE Automation Manual preview
OLE Automation
Бренд: Symantec Страницы: 91
Symantec ALTIRIS INVENTORY 7.0 SP2 - FOR NETWORK DEVICES V1.0 Manual preview
ALTIRIS INVENTORY 7.0 SP2 - FOR NETWORK DEVICES V1.0
Бренд: Symantec Страницы: 148
Autodesk 22505-051400-9000 - AutoCAD Electrical 2008 User Manual preview
22505-051400-9000 - AutoCAD Electrical 2008
Бренд: Autodesk Страницы: 1304
MACROMEDIA FLASH MX 2004 - ACTIONSCRIPT Reference Manual preview
FLASH MX 2004 - ACTIONSCRIPT
Бренд: MACROMEDIA Страницы: 816
KAPERSKY ANTI-VIRUS 5.6 - FOR NOVELL NETWARE Administrator'S Manual preview
ANTI-VIRUS 5.6 - FOR NOVELL NETWARE
Бренд: KAPERSKY Страницы: 130
Navman F-Series F20 Manual Del Usuario preview
F-Series F20
Бренд: Navman Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды