Juniper JUNOS 10.1 - S 5-13-2010 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 204

background image

■

On SRX and J Series devices, the RPM operation will not work for the probe-type
tcp-ping when the probe is configured with the option destination-interface.
[PR/424925]

■

On SRX650 devices, the following loopback features are not implemented for
T1/E1 GPIMs:

■

Line

■

FDL payload

■

Inband line

■

Inband payload

[PR/425040]

■

On J4350 device, multicast traffic is not received when the source and the receiver
are connected to same PE routers. [PR/429130]

■

In J Series xDSL PIMs, mapping between IP CoS and ATM CoS is not supported.
If the user configures IP CoS in conjunction with ATM CoS, the logical interface
level shaper matching ATM CoS rate must be configured to avoid congestion
drops in SAR.

Example:

set interfaces at-5/0/0 unit 0 vci 1.110
set interfaces at-5/0/0 unit 0 shaping cbr 62400 ATM COS
set class-of-service interfaces at-5/0/0 unit 0 scheduler-map sche_map IP COS
set class-of-service interfaces at-5/0/0 unit 0 shaping-rate 62400 ADD IFL SHAPER

[PR/430756]

■

On SRX650 devices, configuring dual and quad T1/E1 framing at the chassis
level has no effect. [PR/432071]

■

On SRX240 devices, the serial interface maximum speed in extensive output is
displayed as 16384 Kbps instead of 8.0 Mbps. [PR/437530]

■

On SRX Series devices, incorrect Layer 2 circuit replication on the backup Routing
Engine might occur when you:

■

Configure nonstop routing (NSR) and Layer 2 circuit standby simultaneously
and commit them

■

Delete the NSR configuration and then add the configuration back when
both the NSR and Layer 2 circuits are up

As a workaround:

1.

Configure the Layer 2 circuit for non-standby connection.

2.

Change the configuration to standby connection.

3.

Add the NSR configuration.

[PR/440743]

■

On SRX210 Low Memory devices, the E1 interface will flap and traffic will not
pass through the interface if you restart forwarding while traffic is passing through
the interface. [PR/441312]

Issues in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

■

147

Issues in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

«
...
145
146
147
148
149
...
»

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Бренд: Canon Страницы: 90

TV708LL/A - NeatWorks For Mac

Бренд: NeatWorks Страницы: 33

Бренд: Sun Microsystems Страницы: 38

Бренд: Extreme Networks Страницы: 546

ExtremeWare 7.5

Бренд: Extreme Networks Страницы: 2546

Document centre 490

Бренд: Xerox Страницы: 102

ETERNUS VSS Hardware Provider 2.1

Бренд: Fujitsu Страницы: 134

Бренд: Fujitsu Страницы: 302

PFU Rack2-Filer

Бренд: Fujitsu Страницы: 463

Eternus web GUI

Бренд: Fujitsu Страницы: 635

Бренд: Fujitsu Страницы: 64

2950C-24 - Catalyst Switch - Stackable

Бренд: Cisco Страницы: 18

CONFERENCING EXTENSIONS - ADMINISTRATOR GUIDE FOR MICROSOFT EXCHANGE

Бренд: Cisco Страницы: 61

Cisco mds 9124 - fabric switch

Бренд: Cisco Страницы: 9

Бренд: Cisco Страницы: 16

Cisco MDS 9020 - Fabric Switch

Бренд: Cisco Страницы: 22

Бренд: Cisco Страницы: 13

Cisco mds 9124 - fabric switch

Бренд: Cisco Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды