Juniper JUNOS 10.1 - S 5-13-2010 Скачать руководство пользователя страница 126

Страница: 126 / 204

save
reset

Once the system is booted from the USB storage device, take a snapshot on
the external CompactFlash using the

request system snapshot media external

command.

NOTE:

Once the snapshot has been taken on the external CompactFlash, we

recommend you to set the

ext.cf.pref

at the U-boot prompt.

Security

■

J Series devices do not support the authentication order

password radius

password ldap

in the

edit access profile

profile-name

authentication-order

command.

Instead, use the

order radius password

ldap password

Known Limitations in JUNOS Release 10.1 for SRX Series Services Gateways and J Series
Services Routers

[accounting-options] Hierarchy

■

On SRX210 and SRX240 devices, the

accounting

source-class

, and

destination-class

statements in the

[accounting-options]

hierarchy level are not

supported.

AX411 Access Point

■

On SRX100 devices, there are command-line interface (CLI) commands and
J-Web tabs for wireless LAN configurations related to the AX411 Access Point.
However, at this time the SRX100 devices do not support the AX411 Access
Point.

Chassis Cluster

On SRX Series and J Series devices, the following features are not supported when
chassis clustering is enabled on the device:

■

All packet-based protocols, such as MPLS, Connectionless Network Service (CLNS),
and IP version 6 (IPv6)

■

Any function that depends on the configurable interfaces:

■

lsq-0/0/0

—Link services Multilink Point-to-Point Protocol (MLPPP), Multilink

Frame Relay (MLFR), and Compressed Real-Time Transport Protocol (CRTP)

■

gr-0/0/0

—Generic routing encapsulation (GRE) and tunneling

■

ip-0/0/0

—IP-over-IP (IP-IP) encapsulation

126

■

Known Limitations in JUNOS Release 10.1 for SRX Series Services Gateways and J Series Services Routers

JUNOS 10.1 Software Release Notes

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Результаты поиска

Содержание JUNOS 10.1 - S 5-13-2010

Отзывы:

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Бренды по названию

Популярные бренды

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

Результаты поиска

Содержание JUNOS 10.1 - S 5-13-2010

Отзывы:

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Бренды по названию

Популярные бренды