manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

"Juniper JUNOS 10.1 - S 5-13-2010" - это последнее обновление программного обеспечения от Juniper Networks. В этом выпуске содержатся важные изменения и улучшения. Вы можете скачать бесплатное руководство по обновлению и использованию этого продукта на manualshive.com. Будьте в курсе всех нововведений с нашими Release Notes.

Поделиться
Скачать
background image

You can issue 

show snmp mib walk dot3StatsTable

, 

show snmp mib walk

dot3PauseTable

, and 

show snmp mib walk dot3ControlTable

 commands to display

the output at the table level.

■

When you issue the 

request system power-off

 command, the switch halts instead

of turning off power.

■

In the J-Web interface, the Ethernet Switching monitoring page might not display
monitoring details if there are more than 13,000 MAC entries on the switch.

■

In the J-Web interface, changing the port role from Desktop, Desktop and Phone,
or Layer 2 Uplink to another port role might not remove the configurations for
enabling dynamic ARP inspection and DHCP snooping.

■

On EX8200 switches, if IS-IS is enabled on routed VLAN interfaces (RVIs), IS-IS
adjacency states go down and come up after a graceful Routing Engine switchover
(GRES).

■

When an external RADIUS server goes offline and comes back online after some
time, subsequent captive portal authentication requests might fail until the 

authd

daemon is restarted. As a workaround, you can configure the revert interval—the
time after which to revert to the primary server—and restart the 

authd

 daemon.

■

Momentary loss of an inter-Routing Engine IPC message might trigger the alarm
that displays the message 

Loss of communication with Backup RE

. There is no

functionality affected.

Interfaces

■

EX Series switches do not support queued packet counters. Therefore, the queued
packet counter in the output of the 

show interfaces 

interface-name

 extensive

command always displays a count of 0 and is never updated.

■

The following message might appear in the system log:

Resolve request came for an address matching on Wrong nh nh:355, 
type:Unicast...?

You can ignore this message.

■

On EX3200 and EX4200 switches, when port mirroring is configured on any
interface, the mirrored packets leaving a tagged interface might contain an
incorrect VLAN ID.

■

On EX8200 switches, port mirroring configuration on a Layer 3 interface with
the output configured to a VLAN is not supported.

■

On EX8200 switches, when an egress VLAN that belongs to a routed VLAN
interface (RVI) is configured as the input for a port mirroring analyzer, the
analyzer incorrectly appends a dot1q (802.1Q) header to the mirrored packets
or does not mirror any packets at all. As a workaround, configure a port mirroring
analyzer with each port of the VLAN as egress input.

■

The following interface counters are not supported on routed VLAN interfaces
(RVIs): local statistics, traffic statistics, and transit statistics.

190

■

Limitations in JUNOS Release 10.1 for EX Series Switches

JUNOS 10.1 Software Release Notes

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Canon PowerShot A590 IS Software User'S Manual preview
PowerShot A590 IS
Бренд: Canon Страницы: 49
M-Audio SESSION Quick Start Manual preview
SESSION
Бренд: M-Audio Страницы: 6
Cabletron Systems Element Manager 2.1 User Manual preview
Element Manager 2.1
Бренд: Cabletron Systems Страницы: 108
Emerson Smart Wireless Navigator Reference Manual preview
Smart Wireless Navigator
Бренд: Emerson Страницы: 22
Emerson Site Manager User Manual preview
Site Manager
Бренд: Emerson Страницы: 130
Fender G-DEC 3 MUSTANG FUSE 2-0 Manual preview
G-DEC 3 MUSTANG FUSE 2-0
Бренд: Fender Страницы: 12
Mustek 1200 CP User Manual preview
1200 CP
Бренд: Mustek Страницы: 28
Internet Security Systems RealSecure User Manual preview
RealSecure
Бренд: Internet Security Systems Страницы: 126
Adobe ILLUSTRATOR CS2 12.0.1 Manual preview
ILLUSTRATOR CS2 12.0.1
Бренд: Adobe Страницы: 6
Adobe 22011302 Manual preview
22011302
Бренд: Adobe Страницы: 8
Adobe 38043740 - ColdFusion Standard - Mac Manual preview
38043740 - ColdFusion Standard - Mac
Бренд: Adobe Страницы: 87
Adobe 38039927 - Fireworks CS3 - PC Using Instructions preview
38039927 - Fireworks CS3 - PC
Бренд: Adobe Страницы: 369
Adobe InDesign 2.0 Help Manual preview
InDesign 2.0
Бренд: Adobe Страницы: 478
Red Hat CERTIFICATE SYSTEM 7.3 - ADMINISTRATION Administration Manual preview
CERTIFICATE SYSTEM 7.3 - ADMINISTRATION
Бренд: Red Hat Страницы: 554
FarmerGPS FarmerGPS User Manual preview
FarmerGPS
Бренд: FarmerGPS Страницы: 60
MINOLTA-QMS PageScope Software Manual preview
PageScope
Бренд: MINOLTA-QMS Страницы: 60
IBM VIAVOICE 10-STANDARD EDITION User Manual preview
VIAVOICE 10-STANDARD EDITION
Бренд: IBM Страницы: 124
IBM ZVSE ROADMAP Manual preview
ZVSE ROADMAP
Бренд: IBM Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды