manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

"Juniper JUNOS 10.1 - S 5-13-2010" - это последнее обновление программного обеспечения от Juniper Networks. В этом выпуске содержатся важные изменения и улучшения. Вы можете скачать бесплатное руководство по обновлению и использованию этого продукта на manualshive.com. Будьте в курсе всех нововведений с нашими Release Notes.

Поделиться
Скачать
background image

■

EX Series switches do not support IPv6 interface statistics. Therefore, all values
in the output of the 

show snmp mib walk ipv6IfStatsTable

 command always display

a count of 0.

■

The 

show interface detail | extensive

 command might display double counting of

packets or bytes for the transit statistics and traffic statistics counters. You can
use the counter information displayed under the 

Physical interface

 section of the

output.

■

When a virtual management Ethernet (VME) interface is used as a default gateway
and the VME interface is the indirect next hop for any route, the route might not
change dynamically and could always point to the VME interface.

Related Topics

■

New Features in JUNOS Release 10.1 for EX Series Switches on page 184

■

Changes in Default Behavior and Syntax in JUNOS Release 10.1 for EX Series
Switches on page 187

■

Outstanding Issues in JUNOS Release 10.1 for EX Series Switches on page 191

■

Resolved Issues in JUNOS Release 10.1 for EX Series Switches on page 194

■

Errata in Documentation for JUNOS Release 10.1 for EX Series Switches on
page 198

■

Upgrade and Downgrade Issues for JUNOS Release 10.1 for EX Series Switches
on page 198

Outstanding Issues in JUNOS Release 10.1 for EX Series Switches

The following are outstanding issues in JUNOS Release 10.1R1 for EX Series switches.
The identifier following the description is the tracking number in our bug database.

NOTE:

PRs 300576, 403842, 409934, 415569, 415748, 429589, 440611, 455670,

and 488318, which were included in the earlier release notes as outstanding issues,
have been removed, because these issues are not applicable to JUNOS Release 10.1R2
for EX Series switches.

Access Control and Port Security

■

If you configure the RADIUS server 

revert-interval 

interval

 option, the switch does

not attempt to reconnect to the unreachable server after the revert interval has
elapsed. [PR/304637]

Bridging, VLANs, and Spanning Trees

■

There might be traffic loss on VLANs learned through MVRP during GRES. After
the GRES, there will not be any traffic loss. [PR/458303]

Outstanding Issues in JUNOS Release 10.1 for EX Series Switches

■

191

Outstanding Issues in JUNOS Release 10.1 for EX Series Switches

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

ShoreTel ShoreWare User Manual preview
ShoreWare
Бренд: ShoreTel Страницы: 25
Mitsubishi Electric MELSOFT FR Configurator2 Instruction Manual preview
MELSOFT FR Configurator2
Бренд: Mitsubishi Electric Страницы: 230
Siemens OC130S Installation Instructions Manual preview
OC130S
Бренд: Siemens Страницы: 11
Siemens ID Mouse V 3.1 User Manual preview
ID Mouse V 3.1
Бренд: Siemens Страницы: 28
Siemens ROS User Manual preview
ROS
Бренд: Siemens Страницы: 32
Siemens OpenScape Xpressions PhoneMail User Manual preview
OpenScape Xpressions PhoneMail
Бренд: Siemens Страницы: 110
VMware CLOUD DIRECTOR 1.0 Using preview
CLOUD DIRECTOR 1.0
Бренд: VMware Страницы: 3
VMware VmWare ESX Server 2.12 Deployment Deployment Manual preview
VmWare ESX Server 2.12 Deployment
Бренд: VMware Страницы: 34
VMware VCM 5.3 Manual preview
VCM 5.3
Бренд: VMware Страницы: 34
Ulead DVD MOVIEFACTORY 3 User Manual preview
DVD MOVIEFACTORY 3
Бренд: Ulead Страницы: 78
AVG ANTI-VIRUS 2011 - REV 2011.07 User Manual preview
ANTI-VIRUS 2011 - REV 2011.07
Бренд: AVG Страницы: 210
AVG ANTI-VIRUS 2011 - REV 2011.06 User Manual preview
ANTI-VIRUS 2011 - REV 2011.06
Бренд: AVG Страницы: 210
Symantec ASSET MANAGEMENT SUITE 7.0 Datasheet preview
ASSET MANAGEMENT SUITE 7.0
Бренд: Symantec Страницы: 4
Symantec ANTIVIRUS 5.2 - FOR NETWORK ATTACHED STORAGE Datasheet preview
ANTIVIRUS 5.2 - FOR NETWORK ATTACHED STORAGE
Бренд: Symantec Страницы: 3
Symantec Altiris CMDB Solution 7.0 Manual preview
Altiris CMDB Solution 7.0
Бренд: Symantec Страницы: 64
KINGDOM COMPUTER OPERATED VIDEO CAMERA SYSTEM Installation & User Manual preview
COMPUTER OPERATED VIDEO CAMERA SYSTEM
Бренд: KINGDOM Страницы: 21
Cabletron Systems SmartCell ZX-250 Installation Manual preview
SmartCell ZX-250
Бренд: Cabletron Systems Страницы: 34
Bacharach Fyrite User Software Installation Manual preview
Fyrite
Бренд: Bacharach Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды