manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

"Juniper JUNOS 10.1 - S 5-13-2010" - это последнее обновление программного обеспечения от Juniper Networks. В этом выпуске содержатся важные изменения и улучшения. Вы можете скачать бесплатное руководство по обновлению и использованию этого продукта на manualshive.com. Будьте в курсе всех нововведений с нашими Release Notes.

Поделиться
Скачать
background image

Because the system is left with only one functional root partition, you should
immediately restore the primary JUNOS Software image. This can be done by installing
a new image using the CLI or J-Web. The newly installed image will become the
primary image, and the device will boot from it on the next reboot.

CLI Changes

This section describes CLI changes when the SRX Series device runs JUNOS Release
10.1 with the dual-root partitioning scheme.

■

Changes to the Snapshot CLI on page 180

■

partition Option with the request system software add Command on page 181

Changes to the Snapshot CLI

On an SRX Series device, you can configure the primary or secondary boot device
with a “snapshot” of the current configuration, default factory configuration, or rescue
configuration. The snapshot feature is modified to support dual-root partitioning.
The options 

as-primary

, 

swap-size

, 

config-size

, 

root-size

, 

var-size

, and 

data-size

 are not

supported on SRX Series devices.

With the dual-root partitioning scheme, performing a snapshot to a USB storage
device that is less than 1 GB is not supported.

With the dual-root partitioning scheme, you must use the 

partition

 option when

performing a snapshot. If the 

partition

 option is not specified, the snapshot operation

fails with a message that the media needs to be partitioned for snapshot.

The output for the 

show system snapshot

 CLI command is changed in devices with

dual-root partitions to show the snapshot information for both root partitions:

user@host> 

show system snapshot media usb

Information for snapshot on       usb (/dev/da1s1a) (primary)

            Creation date: Jul 24 16:16:01 2009

            JUNOS version on snapshot:

            junos  : 10.1I20090723_1017-domestic

            Information for snapshot on       usb (/dev/da1s2a) (backup)

            Creation date: Jul 24 16:17:13 2009

            JUNOS version on snapshot:

            junos  : 10.1I20090724_0719-domestic

NOTE:

You can use the 

show system snapshot media internal

 command to determine

the partitioning scheme present on the internal media. Information for only one root
is displayed for single-root partitioning, whereas information for both roots is
displayed for dual-root partitioning.

180

■

Dual-Root Partitioning Scheme Documentation for SRX Series Services Gateways

JUNOS 10.1 Software Release Notes

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Califone AV Tutor MCFBV1-D Specification preview
AV Tutor MCFBV1-D
Бренд: Califone Страницы: 1
Q-See Remote Client Software V 4.0.1 User Manual preview
Remote Client Software V 4.0.1
Бренд: Q-See Страницы: 72
Inalp Networks SmartWare R2.00 Software Configuration Manual preview
SmartWare R2.00
Бренд: Inalp Networks Страницы: 321
Toshiba HDWC110XK3J1 Quick Start preview
HDWC110XK3J1
Бренд: Toshiba Страницы: 1
Toshiba dynadock Drivers Update preview
dynadock Drivers
Бренд: Toshiba Страницы: 3
Toshiba e-STUDIO Printer/Fax/Scanner/Copier Brochure preview
e-STUDIO Printer/Fax/Scanner/Copier
Бренд: Toshiba Страницы: 4
Toshiba 6F3A4508 Instruction Manual preview
6F3A4508
Бренд: Toshiba Страницы: 53
Benefon TWIG CONFIGURATOR User Manual preview
TWIG CONFIGURATOR
Бренд: Benefon Страницы: 28
3Com 3CR15600 - Enterprise Management Suite Getting Started Manual preview
3CR15600 - Enterprise Management Suite
Бренд: 3Com Страницы: 218
Solid State Logic One Stop Vocal Processing Plug-in Vocalstrip User Manual preview
One Stop Vocal Processing Plug-in Vocalstrip
Бренд: Solid State Logic Страницы: 21
FieldServer FS-8700-23 Driver Manual preview
FS-8700-23
Бренд: FieldServer Страницы: 11
Sun Microsystems VIRTUALBOX 3.0.0 User Manual preview
VIRTUALBOX 3.0.0
Бренд: Sun Microsystems Страницы: 259
FieldServer FS-8704-13 Driver Manual preview
FS-8704-13
Бренд: FieldServer Страницы: 19
Janome Artistic Suite V6 Manual preview
Artistic Suite V6
Бренд: Janome Страницы: 5
IBM High Performance Storage System HPSS Installation Manual preview
High Performance Storage System HPSS
Бренд: IBM Страницы: 311
Novell ZENWORKS ENDPOINT SECURITY MANAGEMENT 3.5 Installation Manual preview
ZENWORKS ENDPOINT SECURITY MANAGEMENT 3.5
Бренд: Novell Страницы: 76
IBM VIAVOICE 10-PRO USB EDITION User Manual preview
VIAVOICE 10-PRO USB EDITION
Бренд: IBM Страницы: 160
Quantum GoVault 40GB Software Manual preview
GoVault 40GB
Бренд: Quantum Страницы: 142

Бренды по названию

Популярные бренды

Загрузить еще бренды