Juniper JUNOS 10.1 - S 5-13-2010 Скачать руководство пользователя страница 187

Страница: 187 / 204

MPLS

■

MPLS enhancements

—On EX3200 and EX4200 switches, MPLS supports class

of service (CoS), IP over MPLS, and fast reroute to reroute the label-switched
path in cases of link failure.

Packet Filters

■

IPv6 support for firewall filters on EX3200 and EX4200 switches

—On EX3200

and EX4200 switches, you can apply match conditions to IPv6 traffic on Layer
3 interfaces, aggregated Ethernet interfaces, and loopback interfaces.

The following are the match conditions applicable to IPv6 traffic:

destination-address

destination-port

destination-prefix-list

icmp-code

icmp-type

interface

next-header

packet-length

source-address

source-port

source-prefix-list

tcp-established

tcp-flags

tcp-initial

traffic-class

The following are the actions and action modifiers applicable to IPv6 traffic:

discard

routing-instance

analyzer

count

forwarding-class

loss-priority

policer

■

Enhancement to the interface match condition on EX8200 switches

—On

EX8200 switches, you can now specify aggregated Ethernet interfaces as match
conditions using the

interface

match condition. You can configure an ingress or

egress firewall filter with an aggregated Ethernet interface as a match condition
and apply the firewall filter to ports, VLANs, and Layer 3 interfaces.

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Результаты поиска

Содержание JUNOS 10.1 - S 5-13-2010

Отзывы:

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Бренды по названию

Популярные бренды

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

Результаты поиска

Содержание JUNOS 10.1 - S 5-13-2010

Отзывы:

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Бренды по названию

Популярные бренды