manualshive.com logo in svg

Juniper JUNOS 10.1 - S 5-13-2010, Руководство по выпуску

"Juniper JUNOS 10.1 - S 5-13-2010" - это последнее обновление программного обеспечения от Juniper Networks. В этом выпуске содержатся важные изменения и улучшения. Вы можете скачать бесплатное руководство по обновлению и использованию этого продукта на manualshive.com. Будьте в курсе всех нововведений с нашими Release Notes.

Поделиться
Скачать
background image

■

The configured TTL set for GRE traffic is set properly for locally generated Routing
Engine packets, but is not set properly for transit packets. [PR/502087: This issue
has been resolved.]

■

In JUNOS Release 10.0, if the MX-MPCs power up while the A-DPCs are offline,
and if ISSU is performed, the MPCs will crash. [PR/502837: This issue has been
resolved.]

■

When an ATM AIS cell is received from the virtual channel under vlan-vci-ccc
encapsulation, the logical interface will be incorrectly marked down. There is no
workaround. [PR/503653: This issue has been resolved.]

■

The yellow marking for the three-color-policers is incorrect. Even after the excess
burst buffer is full, the yellow counters continue to increment at the same rate
as the green buffers. [PR/504192: This issue has been resolved.]

■

Under certain circumstances, the E3 IQ PIC might report bogus CCV, CES, and
CSES alarms. [PR/505921: This issue has been resolved.]

■

The 

show interfaces diagnostics optics interface

 command does not display the

unit of measurement when the received power is in a very low range (power <
5e-10). It shows the value of 0.00 without any unit of measurement. [PR/507653:
This issue has been resolved.]

■

On MX Series routers, the chassisd crashes when the SCB is taken offline and
removed. [PR/510950: This issue has been resolved.]

■

On M7i and M10i routers, the syncer process writes to the file

/var/rundb/chassisd.dynamic.db

 every 30 seconds. [PR/511901: This issue has

been resolved.]

■

Under certain circumstances, the chassisd process might crash on a backup
Routing Engine while a configuration is commited. [PR/512044: This issue has
been resolved.]

Layer 2 Ethernet Services

■

On an MX Series router, the DHCP ACK messages are dropped when a client
Rebind request is processed by a different DHCP server. This issue may occur
in an environment where the provider has multiple DHCP servers for redundancy
purposes. [PR/487138: This issue has been resolved.]

■

The family ISO MTU configured explicitly under the IRB interface logical unit will
decrement by three if you change the interface MTU on the interface that belongs
to the same bridge domain. [PR/493209: This issue has been resolved.]

■

In JUNOS Release 10.0, the MX 960 router displays the following i2c messages
related to the fan:

rocky-re0 /kernel: PCF8584(WR): target ack failure on byte 0
rocky-re0 /kernel: PCF8584(WR): (i2c_s1=0x08, group=0xe, device=0x54)

This is a cosmetic issue and has no impact on the router. [PR/500824: This issue
has been resolved.]

78

■

Issues in JUNOS Release 10.1 for M Series, MX Series, and T Series Routers

JUNOS 10.1 Software Release Notes

Содержание JUNOS 10.1 - S 5-13-2010













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOS 10.1 - S 5-13-2010

Alphasmart AS 3000 Installation And User Manual preview
AS 3000
Бренд: Alphasmart Страницы: 4
McAfee VIRUSSCAN HOME EDITION 7.0 Manual preview
VIRUSSCAN HOME EDITION 7.0
Бренд: McAfee Страницы: 56
Accordiva SecuExpress User Manual preview
SecuExpress
Бренд: Accordiva Страницы: 31
eCopy ShareScan 4.2 Installation And Setup Manual preview
ShareScan 4.2
Бренд: eCopy Страницы: 266
DeLorme Earthmate GPS BT-20 Quick Start Manual preview
Earthmate GPS BT-20
Бренд: DeLorme Страницы: 9
Measurement Computing 374318A-01 User Manual preview
374318A-01
Бренд: Measurement Computing Страницы: 109
Acroprint AcroComm Programming Manual preview
AcroComm
Бренд: Acroprint Страницы: 64
AMX AXWire Instruction Manual preview
AXWire
Бренд: AMX Страницы: 16
GRASS VALLEY MEDIAEDGE3 DCM Datasheet preview
MEDIAEDGE3 DCM
Бренд: GRASS VALLEY Страницы: 2
GRASS VALLEY K2 Dyno PA Configuration Manual preview
K2 Dyno PA
Бренд: GRASS VALLEY Страницы: 60
Fermax Wi-BOX Manual preview
Wi-BOX
Бренд: Fermax Страницы: 8
Autodesk AUTOCAD ELECTRICAL 2005 Getting Started preview
AUTOCAD ELECTRICAL 2005
Бренд: Autodesk Страницы: 88
IBM E027SLL-H - Tivoli Monitoring - PC Troubleshooting Manual preview
E027SLL-H - Tivoli Monitoring - PC
Бренд: IBM Страницы: 310
Quantum GoVault 40GB Quick Start Manual preview
GoVault 40GB
Бренд: Quantum Страницы: 16
Tascam TASCAM PCM Recorder Important Notice preview
TASCAM PCM Recorder
Бренд: Tascam Страницы: 2
Samsung PS63A756T1M Quick Manual preview
PS63A756T1M
Бренд: Samsung Страницы: 13
AudioRealism Bass Line User Manual preview
Bass Line
Бренд: AudioRealism Страницы: 18
MACROMEDIA BREEZE PRESENTER Manual preview
BREEZE PRESENTER
Бренд: MACROMEDIA Страницы: 106

Бренды по названию

Популярные бренды

Загрузить еще бренды