manualshive.com logo in svg

Hyundai R 160 LC-3, Руководство по обслуживанию, Страница: 35 / 459

Поделиться
Скачать
Hyundai R 160 LC-3 Скачать руководство пользователя страница 35

2 - 6

Rotary group
The rotary group consists of drive shaft
(F)(111), cylinder block(141), piston
shoes(151,152), set plate(153), spherical
bush(156), spacer(158) and cylinder
spring(157).   The drive shaft is supported
by bearing(123,124) at its both ends.
The shoe is caulked to the piston to from
a spherical coupling.   It has a pocket to
relieve thrust force generated by loading
pressure and the take hydraulic balance
so that it slides lightly over the shoe
plate(211).   The sub group composed by
a piston and a shoe is pressed against
the shoe plate by the action of the
cylinder spring via a retainer and a
spherical bush.
Similarly, the cylinder block is pressed
against valve plate(313) by the action of
the cylinder spring.

Swash plate group
The swash plate group consists of swash
plate(212), shoe plate(211), swash plate
support(251), tilting bush(214), tilting
pin(531) and servo piston(532).
The swash plate is a cylindrical  part
formed on the opposite side of the sliding
surface of the shoe and is supported by
the swash support.
If the servo piston moves to the right and
left as hydraulic force controlled by the
regulator is admitted to hydraulic
chamber located on both sides of the
servo piston, the swash plate slides over
the swash plate support via the spherical
part of the tilting pin to change the tilting
angle(

҄

)

2. FUNCTION

MAIN PUMP
The pumps may classified roughly into the rotary group performing a rotary motion and working as
the major part of the whole pump function: The swash plate group that varies the delivery rates: And
the valve cover group that changes over oil suction and discharge.

1)

(1) 

(2)

157

211

211

123

111

212

251

532

҄

҄

151
152

531
548

214

124

313

141

158

156

153

Содержание R 160 LC-3












































































































































































































































































































































































































































































Отзывы:

Нет отзывов