Hyundai R 160 LC-3 Скачать руководство пользователя страница 335 | Manualshive

Страница: 335 / 459

background image

8 - 22

DISASSEMBLY
Since the regulator consists of small
precision finished parts, disassembly and
assembly are rather complicated.
For this reason, replacement of a regulator
assembly is recommended, unless there is
a special reason, but in case disassembly is
necessary for an unavoidable reason, read
through this manual to the end before
starting disassembly.

Choose a place for disassembly.
Choose a clean place.
Spread rubber sheet, cloth, or so on on
top of work-bench to prevent parts from
being damaged.

Remove dust, rust, etc. from surfaces of
regulator with clean oil.

(1)

Ɠ
Ɠ

(2)

3)

Remove hexagon socket head screw
(438) and remove cover(C,629)
Cover(C) is fitted with adjusting screw
(C,QI) (628, 925), adjusting ring(C, 627),
lock nut(630), hexagon nut(801) and
adjusting screw(924).
Do not loosen these screws and nuts.
If they are loosened, adjusted pressure-
flow setting will vary.

(4)

Ɠ

Remove hexagon socket head screw
(412, 413) and remove regulator main
body from pump main body.
Take care not to lose O-ring.

(3)

Ɠ

«
...
333
334
335
336
337
...
»

Содержание R 160 LC-3












































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R 160 LC-3

ecot3 PC160LC-8

Бренд: Komatsu Страницы: 51

Бренд: Takeuchi Страницы: 20

Бренд: jcb Страницы: 28

AP Cumberland PNEG-650-1

Бренд: GSI Group Страницы: 10

Бренд: Menzi Muck Страницы: 74

Бренд: Takeuchi Страницы: 235

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды