manualshive.com logo in svg

Hyundai R 160 LC-3, Руководство по обслуживанию, Страница: 232 / 459

Поделиться
Скачать
Hyundai R 160 LC-3 Скачать руководство пользователя страница 232

6 - 13

YES

YES

YES

YES

YES

NO

NO

YES

NO

YES

NO

NO

Is bucket or arm
operation
possible?

Does counterbalance
spool in travel brake
valve move lightly by
hand?

Does the symptom
change when relief
valves in travel
motor are
exchanged?

Has travel control
valve spool
changed over
positively?

Does the symptom
change when front
and rear pump
discharge hoses
are exchanged?

Is travel brake
valve pressure
within standard
level?

Does spool move
lightly when hand
is let free from
control cable?

NO

YES

YES

NO

ڞ

Counter spool in

travel brake valve

is stuck.

Relief valve built in

travel motor is

faulty.

Control system is

defective.

Travel control

valve spool is

stuck.

Travel reduction

unit is faulty.

Travel motor is out

of order.

Hydraulic pump is

broken.

Travel relief valves

are faulty. 

Disassemble and

repair or replace.

Disassemble and

repair.

Disassemble

inspect and

repair.

Disassemble and

repair.

Disassemble and

repair.

Disassemble and

repair.

Disassemble and

repair.

Disassemble and

repair or replace. 

ڞ

5.  TRAVEL SYSTEM

TRAVEL DOES NOT FUNCTION AT ALL ON ONE SIDE

1)

Do not metallic
particles come out
of drain port in
travel reduction
unit?

Cause

Remedy

Does the symptom
change when
LH/RH travel relief
valves are
exchanged?

Содержание R 160 LC-3












































































































































































































































































































































































































































































Отзывы:

Нет отзывов