Hyundai R 160 LC-3 Скачать руководство пользователя страница 12

Страница: 12 / 459

KEEP RIDERS OFF EXCAVATOR

Only allow the operator on the excavator. Keep riders

off.

Riders on excavator are subject to injury such as being

struck by foreign objects and being thrown off the

excavator. Riders also obstruct the operator's view

resulting in the excavator being operated in an unsafe

manner.

MOVE AND OPERATE MACHINE SAFELY

Bystanders can be run over. Know the location of

bystanders before moving, swinging, or operating the

machine.

Always keep the travel alarm in working condition. It

warns people when the excavator starts to move.

Use a signal person when moving, swinging, or

operating the machine in congested areas. Coordinate

hand signals before starting the excavator.

OPERATE ONLY FORM OPERATOR'S SEAT

Avoid possible injury machine damage. Do not start

engine by shorting across starter terminals.

NEVER start engine while standing on ground. Start

engine only from operator's seat.

PARK MACHINE SAFELY

Before working on the machine:

Park machine on a level surface.

Lower bucket to the ground.

Turn auto idle switch off.

Run engine at 1/2 speed without load for 2 minutes.

Turn key switch to OFF to stop engine. Remove key

from switch.

Move pilot control shutoff lever to locked position.

Allow engine to cool.

1 - 3

Содержание R 160 LC-3












































































































































































































































































































































































































































































Результаты поиска

Содержание R 160 LC-3

Отзывы:

Похожие инструкции для R 160 LC-3

Бренды по названию

Популярные бренды

Hyundai R 160 LC-3, Руководство по обслуживанию

Результаты поиска

Содержание R 160 LC-3

Отзывы:

Похожие инструкции для R 160 LC-3

Бренды по названию

Популярные бренды