manualshive.com logo in svg

Hyundai R 160 LC-3, Руководство по обслуживанию, Страница: 339 / 459

Поделиться
Скачать
Hyundai R 160 LC-3 Скачать руководство пользователя страница 339

8 - 26

ASSEMBLY 

For assembly, reverse disassembly
procedures, but pay attention to the
following items.

Always repair parts that were scored at
disassembly.
Get replacement parts ready beforehand.
Mixing  of  foreign  matter  will   cause
malfunction.
Therefore, wash parts well with cleaning
oil, let them dry with jet air and handle
them in clean place.
Always tighten bolts, plugs, etc.   to their
specified torques.
Do  not  fail to coat  sliding  surfaces  with
clean hydraulic oil before assembly.
Replace seals such as O-ring with new
ones as a rule.

(1)

ڸ

ڹ

ں

ڻ

ڼ

4)

Spool

Feedback lever

Put compensating rod(623) into
compensating hole of casing(601).

Put pin force-fitted in lever(1, 612) into
groove of compensating rod and fit lever
(1) to pin force-fitted in casing.

(2)

(3)

Fit spool(652) and sleeve(651) into hole in
spool of casing.
Confirm that spool and sleeve slide
smoothly in casing without binding.
Pay attention to orientation of spool.

(4)

Ɠ

Ɠ

Содержание R 160 LC-3












































































































































































































































































































































































































































































Отзывы:

Нет отзывов